Quantcast
Channel: Latest Discussions - COMSOL Forums
Browsing all 4154 articles
Browse latest View live
↧

Fluid Flow in U-loop

Hi everyone, I have modelled a U-loop with water flowing through inside in 3D, with three different sections (two cylindrical lines and one half of a torus at the bottom). But COMSOL only calculates...

View Article


Running FSI examples, "undefined value found"

Hi!, i am trying to run an fluid-structure example with use of the MEMS module, byt anytime i get the error "undefined value found..." for the variable mod1.v_solid. So i even downloaded the 2d fsi...

View Article


3D geometry imported mesh

hello Saeid, sorry for the later response. was on holiday for about a month. i am using COMSOL 4.3a. i just checked with my computer. It's possible to follow...

View Article

sloshing tank problem with solid structure

Hi all, I was trying several to do the "sloshing_tank" model with container which is elastic material. when I add the container with the sloshing_tank geometry, the free fluid surface did not show- as...

View Article

How to assign different values to dependent variables

Hi, I am just wondering that how it is possible to assign optional values to the dependent variable in some part of the domain ? I always get "Duplicate variable error". Actually I am trying to put...

View Article


One way coupling- A reasonable approximation?

In the tutorial for FSI in a network of blood vessels, it has been narrated at the end in the results and discussion section for Figure 5. " The displacements are in the order of 10um, which suggest...

View Article

3D laminer vortex

hi, I am simulating a block which filled in water, and there is a cylinder prevent the water the block.(the diameter of the cylinder is smaller than the block) I am using laminer flow and hoping to see...

View Article

Error about 'Failed to find consistent initial values. Last time step is not...

Hi, I am a new user of COMSOL. I've set up my reactor geometry model and successfully applied the turbulent flow (stationary condition) in my reactor model. However, when I try to simulate my reactor...

View Article


Prolonged error with "Last Time Step Not Converged"

Dear sir, We were trying out "PIPE FLOW MODULE" as you have suggested. And thanks for the advice, as it has reduced the number of mesh elements to a larger extent. But, we were getting a consistent...

View Article


Single phase flow with heat transfer in vertical tube

Hi, Actually, i am trying to model two phase flow in vertical tube. So, as I am new in COMSOL, i AM STARTING WITH SINGLE PHASE FLOW WITH HEAT TRANSFER IN VERTICAL TUBE. for LAMINAR FLOW my MODEL IS...

View Article

Error with the laminar flow inlet in plasma simulations

Hello! Using the laminar flow for plasma processes I have had some errors when the section of the inlet is small. I am trying to simulate a chamber where the inlet section has a radius of 0.0025 m, so...

View Article

How can I find the flow velocity of a specific coordinate point

Dear all, I would like to ask how can I find the flow velocity of a specific point (x=105, y=2.5) in my channel (it is shown in the picture). In the graph, if I click at any random point I got 3...

View Article

Fluid flow channel in cantilever beam

Hello, My model is the following: a cantilever beam has one longitudinal channel containing a fluid flow. My goal is to find the effects of the fluid flow (viscosity, velocity, size of the channel) on...

View Article


Velocity gradient expression in 2D-axisymmetric

Hello, the velocity gradient tensor for a 2D-axisymmetric problem presents, for the phiphi component, the following expression chns.graduDGphiphi = if(abs(r)<0.0010*h,d(u,r),u/r) does anyone know...

View Article

Multiple-size particle tracing

Hello everyone I have a short question on the particle tracing module. Does anyone know that whether it is possible to simulat particles of different sizes in the same model. How to implement this...

View Article


Surface evaporation, condensation

Hi, I want to model surface evaporation from a water flow at 40 Celsius and observe the consequent condensation on a cold surface. Can you help me with the model that I should use? I could not find...

View Article

How to find temperature variation for a single element in my model

My model has 7 elements as a whole. I am able to plot the temperature variations of the whole model but not for any separate element in the model. I request if somebody helps me know how to plot the...

View Article


old model cannot be reconstructed....

I am attempting to build on a model using Darcy's law to model solute transport under saturated conditions. The original model was built in COMSOL 3.5a, and I get an error message "Old model cannot be...

View Article

Velocity gradient expression in 2D-axisymmetric

Hello, the velocity gradient tensor for a 2D-axisymmetric problem presents, for the phiphi component, the following expression chns.graduDGphiphi = if(abs(r)<0.0010*h,d(u,r),u/r) does anyone know...

View Article

Multiple-size particle tracing

Hello everyone I have a short question on the particle tracing module. Does anyone know that whether it is possible to simulat particles of different sizes in the same model. How to implement this...

View Article
Browsing all 4154 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>