Fixing an Object to a Set Position, Mises Force, Fluid Dynamics
Hello, I am trying to design a 2D microfluidic channel using COMSOL Multiphysics 3.2b. Inside of the channel, I want to fix an object and use COMSOL to calculate the magnitude of the von Mises stress...
View Article2D TRANSIENT Heat Transfer Problem
Hi everyone, I am encountering an error in the time dependent situation - Failed to find consistent initial values, last time steps not converged. I have specified 'initial values' and the required...
View Articlerestraining normal velocity vector in a curved surface
Hi all, I'm trying to emulate a two phase flow with the laminar single phase module, but I could not find a way to restrict the normal velocity from flowing through a curved surface. It's like a slip...
View ArticleMultiphase Flow LS - Air Bubble in Water Cylinder - Conservative forms fails
Hello everybody and thank you in advance for any kind of help you may give, I am trying to simulate a simple kind of scenario, an air bubble in a water cylinder rising due to buoyancy force. I made my...
View ArticleDensity dependent on temperature and solute concentration
Hello, I am trying to couple fluid flow (Darcy's Law), temperature (Heat Transfer in Porous Media), and solute transport (Species Transport in Porous Media). I need the density of water to be dependent...
View Article3D simulations and meshing problems
Hello, I am doing some 3D simulations. I have basically some very small structures on a bigger substrate. I have to use the ignore faces operation to remove the common faces between the substrate and...
View ArticleAny sucessful study for fire simulation by comsol?
Hello! Is the comsol suitable for fire simulation? Another question is any sucessful case for high temperature (100c - 900c)environment air flow simulation with inlet and outlet condition. Since When I...
View Articlehow can set up the inital field velocity for the fluid?
Hello I want to simulate the motion of a nano ball in the liquid. the liquid has a stale field velocity, angular velocity W(r) and has nothing with the angle theta due to symmetry. I would how to set...
View ArticleDe-icing of wing
Hi, I'm doing simulation of deicing of wing due to heating up sections of the leading edge of the wing. However, when I go through all the boundary set up and run the solution. I get an error:...
View ArticleFind Inertial Modes, Eigenvalues for a Sphere of Fluid
I am new to Comsol and I am trying to find the eigenmodes of a rotating sphere filled with water in the rotating frame. I have specified the sphere filled with water with free slip walls, specified...
View ArticleConcentration problem within micromixers: absurd concentrations, no mass...
Hello everybody. I am modelling micromixers and want to check their efficiencies. For that purpose, I first used the Incompressible Navier-Stokes model, to calculate the flow inside my device. I set it...
View ArticleHow to Improve Convergence in Natural Convection
I am wondering how I can improve convergence in my natural convection model. It is a simple model; an isothermal aluminum plate in water. The model starts out fine but as the run continues (transient...
View ArticlePipe flow module / Falied to evluate variable Jacobian
I am working over a simple pipe flow problem, where I encountered with an Jacobial Error saying ; Failed to evaluate variable Jacobian. - Variable: mod1.nipfl.u3 - Geometry: 1 - Boundary: 7 10 13 I...
View ArticleSimulation of Stirling Engine
Hello everybody I'm currently trying to simulate the fluid flow in a stirling engine (beta) which I've built from the following video:www.youtube.com/watch?v=X2qssmxA82U You should try building it;-)...
View ArticleShallow-channel approximation with wetted wall in Laminar Two-Phase Flow
Hello, in earlier versions of COMSOL (eg. 4.1) it was possible to define a wetted wall boundary condition simultaneously with shallow-channel approximation in the two-phase flow physics. However in...
View Articlemagnetohydrodynamic model
Hello. I learned that the latest version of Comsol-u is magnetohydrodynamic model. He was someone kind enough to send me this model? Thank you.
View Articlethermal model
Hi everyone, I am working on a thermal model and used conjugate heat transfer for simulation. My problem is when i want to calculate the thermal efficiency of the flowing fluid (cooling) by identifying...
View ArticleHow to add gas velocity in turbulent bubbly phase?
Hi, I am trying to model a gas-liquid system. I selected turbulent bubbly flow model as it is based on Euler-Euler equation. But I don't know how to add gas velocity field at inlet. Liquid phase in my...
View ArticleFixing an Object to a Set Position, Mises Force, Fluid Dynamics
Hello, I am trying to design a 2D microfluidic channel using COMSOL Multiphysics 3.2b. Inside of the channel, I want to fix an object and use COMSOL to calculate the magnitude of the von Mises stress...
View Article2D TRANSIENT Heat Transfer Problem
Hi everyone, I am encountering an error in the time dependent situation - Failed to find consistent initial values, last time steps not converged. I have specified 'initial values' and the required...
View Article