Which interface choose for fluid flow with heat transfer
Good day! I would like to ask for an advice. I wish to solve the following problem: I have a plate of a solid material with low thermal conductivity. There is a pipe with cold water inside the plate....
View ArticleTracking Residual
I need to track the residual in my simulation in order to represent how closely the governing equations are being represented. I know comsol keeps track of residual since ive had several errors...
View ArticleConvergence issues with level-set conservative form
Hello Everyone, I am trying level-set conservative form for droplet generation in flow focusing device. I have tried the following: (a) non-conservative form: it converges well but mass conservation is...
View ArticleHow to simulate the water boiling by Level-Set method
There is a good example simulating water boiling by phase field. I am trying to use the Level-Set method. However, I was frustrated by many times of failure. My problem is how to deal with the...
View ArticleSimulation of Stirling Engine
Hello everybody I'm currently trying to simulate the fluid flow in a stirling engine (beta) which I've built from the following video:www.youtube.com/watch?v=X2qssmxA82U You should try building it;-)...
View Articlewhat's different between 'frequency domain' and 'frequency domain,...
Hello guys I'm simulating a cantilever sensor, which contains three modules, 'laminar flow', 'electric currents', and 'particle tracing in fluid flow'. For this, in electric currents module, AC...
View ArticleSimulating a rheometer
Hi Everyone, I'm a bit new to Comsol so sorry if this is a dumb question. I'm trying to simulate a rheometer in my lab. It's basically a cone in a petri dish. For simplicity I'm using 2-D and have...
View ArticleQuestion about model ID:9408
Dear Friends, I was checking model id 9408, it's vibrating beam in fluid flow, my questions: 1- I like to have Sine vibration for beam, I replaced point load in this model that it'a Gaussian pulse with...
View ArticleLaminar outflow boundary condition does not converge!
Hello everyone, I am new to this programm and want to simulate the first part of a streamed circular duct. It serves as an hydrodynamical entry length to develop the velocity flow profile. In the...
View ArticleCan I access each cell's residual
Hi, I was wondering if it is possible to access the flow residuals from a UDF? I need to be able to access the momentum and continuity residual for every cell in the computational mesh. Thanks, Farid
View ArticleForced convection - horizontal flow against a plane sheet with a blunt edge
Hi folks, that's my first time I'm working with COMSOL MULTIPHYSICS and I'm trying to simulate a horizontal flow against a plane sheet with a blunt edge. I use convective and conductive (cc) and...
View ArticleIsothermal contour normal vectors
Hi All, Background: I am mapping the temperature gradients at the solidification front of a laser generated melt pool. However the gradients need to be measured in the direction normal to the...
View Article3D simulation of drop coalesnce
I am try to solve the two drop coalescence by applying the two phase flow and phase field method in comsol. 2D it solve the problem very accurately. but 3D is not. kindly suggest any modification need...
View Article3D electrocoalescence with multiple inlets
Hi I have based my simulation on the electrocoalescence example except I have two phases coming in at the inlet. As such I have defined an explicit boundary selection for each inlet phase and have two...
View ArticleNatural Convection in a Box
Hi, I'm trying to get that cats eye picture of natural convection in a box. My solution converges but I dont see any streamlines. If someone can spot a mistake that I made, it would be helpful. I am...
View ArticleTorque from Shear Stress Integration
Hello, I have been working on a model of a flat plate very near the wall of a duct with air flowing through it. In order to find the forces acting on this plate, I have been integrating T_stress over...
View Articleapplying reaction force operator on an inner boundary
Hello, I'm trying to calculate normal mass and heat flux on an inner geometry boundary (no boundary condition is applied on the boundary) using the reacf() oprator (reacf(p) for mass and reacf(T) for...
View ArticleWhich interface choose for fluid flow with heat transfer
Good day! I would like to ask for an advice. I wish to solve the following problem: I have a plate of a solid material with low thermal conductivity. There is a pipe with cold water inside the plate....
View ArticleModelling transport of species in porous media
I am trying to solve a similar problem. I have looked at all the available mph models. Could you supply an example of your model and I could take a look at it. Perhaps we could benefit from the mutual...
View Article